Precor Electronic Console with the Pulse Feature 903 Manuale Utente

page 1Owner’s ManualAssembly and OperationElectronicConsolewith thePulse FeatureRUSA

page 103. Insert the long screws through the mounting holes onthe clamp. See Diagram 7. You may need to squeezethe ends of the clamp together to insta

page 117. Position the electronic console over the handrailclamp and plug the connector into the receptacle. SeeDiagram 8. Do not force the connection

page 12Installing the Mounting PadsTwo adhesive-backed foam pads (one thick and one thin pad)accompany your electronics option package. The thick pad

page 132. Remove the paper backing from one side of the thick padand press the pad firmly in place between the roller guardand the deck of the treadmi

page 145. Remove the paper backing from one side of the thin padand press the pad firmly in place onto the flywheel. SeeDiagram 11.6. To mount the mag

page 151. Remove the paper from the adhesive strip on theflywheel’s foam mounting pad.2. Wipe the back of the magnet with a dry clean, soft cloth.Posi

page 16Diagram 135. Remove the paper to expose the adhesive strip that is onthe foam mounting pad. Press the reed switch onto thepad. Be sure that the

page 17Using the Electronic ConsoleThe electronic console provides multiple features and an easy-to-read LCD display that lets you review your progres

page 18To hold on one particular feature, press the SELECT buttonwhile the feature (such as TIME) is being displayed. The iconstops blinking. To retur

page 19PULSE—shows your heartrate if you have attached andare using the ear clip. Refer toChoosing a Target HeartRate. You can also set analarm to ind

page 2Safety InformationPlease review and observe the following safety guidelines whenassembling and using the Precor 903/904 electronic console:Befor

page 20Setting the DISTANCEIf you have a specific number of kilometers that you wantto travel during your workout, use this feature. An alarmsounds wh

page 21Diagram 15 shows your recommended heart rate trainingzone which is calculated using your age and your maxi-mum attainable heart rate. The chart

page 22Note: The located in the upper left corner of thedisplay begins to blink once a heart rate is detected.2. When the (PULSE) icon is displa

page 23Maintaining the Electronic ConsoleUse a damp, clean cloth after every workout to wipe off anyperspiration that might have fallen on the electro

page 24Diagram 17Diagram 182. Disconnect the reed switch wire by gently pulling theconnector out of the receptacle. See Diagram 17.3. Remove the back

page 25Diagram 195. Reinsert two fresh batteries. Remove the existingbatteries from the unit and reinsert two fresh (A-76type) alkaline batteries. The

page 26Appendix A Put magnet mounting pad here Shaft cut-awayMake a copy of this template or trace the pattern onto a different sheet of paper b

page 27USARPrecor IncorporatedP.O. Box 3004Bothell, WA USA 98041-3004Precor is a registered trademark of Precor Incorporated.© 1996 Precor Incorporate

page 3Table of ContentsSafety Information ... 2 Obtaining Service ...

page 4Before You BeginThank you for purchasing the easy-to-use electronicconsole option for your Precor 903 Manual or 904 Total BodyTreadmill. Before

page 5Installing the Electronic ConsoleThe handrail clamp can be used on either the 903 or 904treadmill. However, the steps used to install the consol

page 63. Unlock and remove the mounting bracket from the back ofthe electronic console. Unlock the mounting bracket bypushing it down toward the base

page 75. Secure the mounting bracket and clamp by inserting thetwo long screws through the mounting holes. You mayneed to squeeze the ends of the clam

page 8Diagram 59. Attach the C clips around the handrail as shown inDiagram 5. Position the slight protrusion on the C cliparound the reed switch wire

page 9904 Assembly ProceduresTo install the 904 electronic console, take the following steps:1. Remove the handrail clamp from its box. Take the long