Precor EFX546 Manuale di Servizio Pagina 89
- Pagina / 118
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
C546 Elliptical Fitness Crosstrainerl
Page 89
7. Replace mounting nut that secures the speed sensor to the frame.
8. Reconnect the speed sensor cable to the lower PCA.
9. Re-install the rear cover, then check the operation of the C546 as described in Section Four.
10. Remove the left rear cover.
11. Disconnect the speed sensor cable from the lower PCA.
Diagram 7.17B - Speed Sensor Mounting (version 3)
12. Remove the mounting nut that secures the speed sensor assembly to the frame. Thread the
speed sensor out of the frame.
Replacing the Speed Sensor Assembly
13. Thread the replacement speed sensor into the frame as far as possible. Rotate the
crankarm until the magnet in the crankarm is next to the speed sensor. Thread the speed
sensor out of frame, as required, to set the distance between the speed sensor and the
magnet to 1/4 inch.
14. Replace mounting nut that secures the speed sensor to the frame.
15. Reconnect the speed sensor cable to the lower PCA.
16. Re-install the left rear cover, then check the operation of the C546 as described in Section
Four.
Speed Sensor
- General Information 4
- Tools Required 4
- After Each Use 5
- Daily Maintenance 5
- Weekly Maintenance 5
- Quarterly Maintenance 6
- Standard Access Codes 7
- Diagram 3.1 - C546 Display 9
- ▼ and RESISTANCE ▲ keys 10
- (version 2,3) 11
- Procedure 13
- 5. Press ENTER, to exit 14
- Diagram 5.4 - Drive Unit 27
- Diagram 5.6 - Stub Tensioner 29
- Interconnect Cables 30
- Version 2,3 32
- 47. Replace the rear cover 33
- (version 1) 34
- Diagram 6.1 - Upper PCA 34
- Diagram 7.2- Frame Cover 54
- Removing the Lower PCA 63
- Diagram 7.6 - Lower PCA 63
- Replacing the Lower PCA 64
- Diagram 7.7 - Lower PCA 65
- Version 2,3 units 69
- Removing the Line Filter 73
- Replacing the Line Filter 73
- Removing the ON/OFF Switch 74
- Replacing the ON/OFF Switch 74
- Removing the Lift Motor 75
- Replacing the LIft Motor 76
- Removing a Crankarm Assembly 78
- Diagram 7.13 - Crankarm 78
- 14 mm. Bolt 78
- Crankarm 78
- Stairarm 78
- Procedure 5.3 86
- 17. Replace the cover 86
- Speed Sensor 89
- Assembly 90
- - Replacing a Wheel Assembly 93
- Diagram 7.20 - Ramp Pivot 97
- Diagram 7.21 - Ramp Assembly 98
- (version 1, 2)) 101
- Interconnect 102
- Center Handrail 102
- Frame Tube 102
- Diagram 7.24 - Clamp Mounting 103
- Page 104 104
- Page 106 106
- Page 108 108
- Page 110 110
- Page 112 112
- Page 114 114
- Page 116 116
- Page 118 118
Poulan Pro PB195H42LTX LAWN TRACTOR podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Sprzęt ogrodniczy Poulan Pro PB195H42LTX LAWN TRACTOR.
Dostarczamy 2 pdf podręczników Poulan Pro PB195H42LTX LAWN TRACTOR do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commenti su questo manuale